Week Ending December 30, 2023

The following new procedure(s) were added:

The following procedure(s) were updated:

1. Oil Filter - Rear Drive Unit (Plaid) (Remove and Replace) - Added a Note to state that a Toolbox routine has a 10 minute duration, but can be stopped early by pressing the accelerator pedal.

Week Ending December 23, 2023

The following procedure(s) were updated:

1. Brake Fluid Bleed/Flush (Remove and Replace) - Updated brake stiffness routine.
2. Brake Lines - LH Sill (Remove and Replace) - Updated brake stiffness routine.
3. Camera - Interior (Remove and Replace) - Fixed errors.
4. Noise Absorber - Motor Bay - Front Bulkhead (Remove and Replace) - Updated brake stiffness routine.
5. Pedal Assembly (Remove and Replace) - Removed brake stiffness routine.
6. Switch - Brake Light (Remove and Replace) - Removed brake stiffness routine.

Week Ending December 16, 2023

The following procedure(s) were updated:

1. Aero Lens - Instrument Panel (Remove and Replace) - Added IP sub assembly step.
2. Car Computer (Remove and Replace) - Added URL to Toolbox Panel.
3. Door Glass - Front - LH (Adjust) - Updated the original nonadjustable correction code to the new adjustable one.

Week Ending December 8, 2023

The following procedure(s) were updated:

1. Four Wheel Alignment Check and Adjust - Revised procedure to be in line with latest PDS validation.
2. Ride Height (Adjust) - Revised procedure to be in line with latest PDS validation.

Week Ending December 1, 2023

The following procedure(s) were updated:

1. Reflex Marker - Taillight - RH (Global) (Remove and Replace) - Reorganized the procedure.
2. Sensor - Pressure and Temperature (PT) - Low Pressure (Remove and Replace) - Reorganized the procedure.
3. Taillight - LH (Global) (Remove and Replace) - Reorganized the procedure.
4. Taillight - RH (Global) (Remove and Replace) - Reorganized the procedure.

Week Ending November 25, 2023

The following procedure(s) were updated:

1. Door Assembly - Front - LH (Remove and Replace) - Replaced Toolbox routines by routines using the touchscreen.
2. Handle - Exterior Release - Door - Front - LH - Generation 3.0 (Remove and Replace) - Replaced Toolbox routines by routines using the touchscreen.
3. Handle - Exterior Release - Door - Rear - LH (Remove and Replace) - Replaced Toolbox routines by routines using the touchscreen.
4. Light - Brake - High Mounted (Remove and Replace) - Updated template availability from external link.
5. Module - Body Controller - Security (Remove and Replace) - Updated security controller configuration steps.
6. Module - Steering Column Control (Remove and Replace) - Replaced Toolbox routine PROC-VCLEFT_X_STEERING-COLUMN-CALIBRATIONSearch for routine in ToolboxSteering Column Calibration with PROC_STEERING_COLUMN_CALIBRATIONSearch for routine in ToolboxSteering Column Calibration RoutineChassis / Steering - Calibrate Steering Column.
7. Sensor - Pressure and Temperature (PT) - High Pressure (Remove and Replace) - Reorganized the procedure.
8. Tire Rotation - Added step to reset learned tire values.

Week Ending November 18, 2023

The following procedure(s) were updated:

1. Hose - Supermanifold To Offboard Battery Pump (Remove and Replace) - Reorganized the procedure.
2. Insulator - Top Cowl (Remove and Replace) - Reorganized the procedure.
3. Module - Body Controller - LH (Remove and Replace) - Updated post-replacement routine.
4. Module - Body Controller - RH (Remove and Replace) - Updated post-replacement routine.

Week Ending November 11, 2023

The following procedure(s) were updated:

1. HV Battery (AWD) (Remove and Replace) - Updated UI steps.
2. Hose - Front Drive Unit Heat Exchanger to Supermanifold (Remove and Replace) - Reorganized the procedure.
3. Hose - Offboard Powertrain Pump To Radiator (Remove and Replace) - Reorganized the procedure.
4. Hose - Return - Powertrain (Remove and Replace) - Reorganized the procedure.
5. Hose - Supermanifold To Offboard Powertrain Pump (Remove and Replace) - Reorganized the procedure.
6. Pump - Coolant - Battery - Offboard (Remove and Replace) - Reorganized the procedure.
7. Pump - Coolant - Powertrain - Radiator (Remove and Replace) - Reorganized the procedure.
8. Steering Yoke/Wheel (Remove and Replace) - Added a note to install the correct airbag variant.

Week Ending November 4, 2023

The following procedure(s) were updated:

1. Battery - LV (Remove and Replace) - Replaced Toolbox 3 CAN redeploy with Service Mode UI software reinstall.
2. Charge Port (EMEA) (Remove and Replace) - Corrected nut size and torque figure in Installation step 5.
3. Subframe Assembly - Rear (Remove and Install) - Added steps for dummy plug on HV battery RH HV header.

Week Ending October 28, 2023

The following new procedure(s) were added:

1. Gateway Configuration (Display and Change)

The following procedure(s) were updated:

1. 3 Way Coolant Valve - Radiator Bypass (Remove and Replace) - Reorganized the procedure.
2. A/C Compressor (Remove and Replace) - Reorganized the procedure.
3. Acoustic Blanket - Compressor (Remove and Replace) - Reorganized the procedure.
4. A/C Refrigerant (Recovery and Recharge) - Reorganized the procedure.
5. Brake Caliper - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.
6. Brake Pads - Rear (Remove and Replace) - Updated EPB Service Mode reference.
7. Brake Pads and Rotors - Rear - Set (Remove and Replace) - Updated EPB Service Mode reference.
8. Brake Rotors - Rear - Set (Remove and Replace) - Updated EPB Service Mode reference.
9. Hose - HV Battery to 3 Way Valve (Remove and Replace) - Reorganized the procedure.
10. Hose - RH Front Sill to Underhood (Remove and Replace) - Reorganized the procedure.
11. Module - Body Controller - Security (Remove and Replace) - Updated post-replacement Toolbox routines.
12. Park Brake Caliper - Release - Updated with new Toolbox routines.
13. Seal - Axle - Rear Drive Unit - LH (Remove and Replace) - Updated EPB Service Mode reference.
14. Seal - Axle - Rear Drive Unit - LH (Plaid) (Remove and Replace) - Updated EPB Service Mode reference.
15. Seat Assembly - 1st Row - LH (Remove and Replace) - Updated gateway configuration value to be set when replacing a seat not equipped with a Farside Air Bag by a seat equipped with a Farside Air Bag.
16. Steering Yoke/Wheel (Remove and Replace) - Added a warning.
17. TPMS (Sensor ID Tool Learn) - Updated procedure and Toolbox routine.

Week Ending October 21, 2023

The following new procedure(s) were added:

1. SIM Card - Car Computer (Remove & Replace)

The following procedure(s) were updated:

1. Actuator - Vane - Center Console - LH (Remove and Replace) - Reorganized the procedure.
2. Air Wave Assembly - Center Console (Remove and Replace) - Reorganized the procedure.
3. Brake Caliper - Rear - LH (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
4. Brake Pads and Rotors - Rear - Set (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
5. Brake Pads - Rear (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.
6. Brake Rotors - Rear - Set (Remove and Replace) - Added step to make sure caliper piston face is aligned for Mando calipers.

Week Ending October 14, 2023

The following procedure(s) were updated:

1. Harness - Sub-Assembly - Instrument Panel (Remove and Replace) - Reorganized the procedure.
2. Oil Filter - Front Drive Unit (Remove and Replace) - Reorganized the procedure.
3. Oil Pump - Front Drive Unit (Remove and Replace) - Reorganized the procedure.

Week Ending October 7, 2023

The following procedure(s) were updated:

1. Oil Pump - LH - Rear Drive Unit (Plaid) (Manual Drain) (Remove and Replace) - Corrected EDF2 gearbox fluid.
2. Touchscreen (HW3) (Remove and Replace) - Added step for checking vehicle firmware version.