Release Notes June-September 2022
Week Ending October 1, 2022
The following procedure(s) were updated:
- Brake Pads - Burnishing - Added correction code for carbon ceramic brakes
- Inverter - Front Drive Unit (Remove and Replace)
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace)
- Toolbox 3 (Connect and Disconnect) and Service Mode Plus - Locally connecting Toolbox 3 to the vehicle now automatically enables Service Mode Plus.
Week Ending September 24, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- HV Battery (AWD) (Remove and Install) - Change correction code from 16010101 to 16010201 and added AWD
- HV Battery (AWD) (Remove and Replace) - Change correction code from 16010102 to 16010202 and added AWD
- Module - Bluetooth Low Energy (BLE) - Rear (Remove and Replace) - Added Toolbox routine and Service Redeploy steps.
Week Ending September 17, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Active Damper - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
- Curtain Airbag - LH (Remove and Replace) - Updated steps for releasing rear of headliner.
- Decor - Center Console (Remove and Replace) - Added torque specs for the décor and brightstrip.
- Hub - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
- Knuckle - Suspension - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
- - Added step to refer to Alignment Requirement.
- Link - Aft - Upper - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
- Link - Fore - Lower - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
- - Added step to refer to Alignment Requirement.
- Panel - Lower Rear - Center Console (Remove and Replace) - change correction code to 15195202
- Stabilizer Bar - Rear (Remove and Replace) - Added step to refer to Alignment Requirement.
- Subframe Assembly - Rear (Plaid) (Remove and Replace) - Added step to refer to Alignment Requirement.
- Subframe Assembly - Rear (Plaid) (Remove and Install) - Added step to refer to Alignment Requirement.
- Subframe Assembly - Rear (Remove and Install) - Added step to refer to Alignment Requirement.
- Subframe Assembly - Rear (Remove and Replace) - Added step to refer to Alignment Requirement.
- Toe Link Assembly - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
Week Ending September 10, 2022
The following procedure(s) were updated:
- Check Base - Magnetic - Sun Visor - LH (Remove and Replace) - Change “driver” to LH
- Sun Visor - LH (Remove and Replace) - Updated procedure and change title from “driver” to “LH”
- Vehicle HV Disablement Procedure - Added information for mulitmeter check
- Module - Bluetooth Low Energy (BLE) - Front (Remove and Replace) - Added steps for service redeploy and endpoint comm routines.
Week Ending September 3, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Charge Port (Remove and Replace) - Updated procedure
- HV Harness - HV Battery to Front Drive Unit (Remove and Replace) - Updated procedure
- Inverter - Front Drive Unit (Remove and Replace) - Added check for 6 O-ring phase out cover or replacement.
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Added check for 6 O-ring phase out cover or replacement.
- - Added check for 6 O-ring phase out cover or replacement.
Week Ending August 27, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- HV Harness - HV Battery To A/C Compressor (Remove and Replace) - Updated procedure
- HV Harness - HV Battery to Rear Drive Unit - LH (Plaid) (Remove and Replace) - Updated procedure
- Module - ECU - Occupant Classification System (OCS) - Front Passenger (Remove and Replace) - Added Note: If a new OCS ECU module is being installed, make sure to use 1599693-00-D or later.
- Oil Pump - LH - Rear Drive Unit (Plaid) (Manual Drain) (Remove and Replace) - Updated oil drain and fill steps.
Week Ending August 20, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Glass - Roof - Fixed (Remove and Install) - Updated with steps for fixed glass roofs without urethane extrusions.
- Glass - Roof - Fixed (Remove and Replace) - Updated with steps for fixed glass roofs without urethane extrusions.
- Inverter - Front Drive Unit (Remove and Replace) - Updated to latest GSD validation.
Week Ending August 13, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- HV Battery (AWD) (Remove and Replace) - Modified SoC percentage for shipping HV battery by air from 25% to 30%.
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Updated torque values for phase out cover bolts and inverter mounting bolts, and updated step to reuse inverter mounting bolts.
- - Updated torque values for phase out cover bolts and inverter mounting bolts, and updated step to reuse inverter mounting bolts.
- Oil Pump - LH - Rear Drive Unit (Plaid) (Manual Drain) (Remove and Replace) - Removed unnecessary step to configure oil pump.
- TPMS (Sensor ID Drive Learn) - Updated procedure
- TPMS (Sensor ID Tool Learn) - Updated procedure
Week Ending August 6, 2022
The following procedure(s) were updated:
- Knee Airbag - Driver (Remove and Replace) - Improved guidance for disconnecting electrical connectors, provided videos.
Week Ending July 30, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Cover - Back Rest - Driver (Remove and Replace) - Updated link to airbag installation video.
- Cover - Back Rest - Driver (With Inboard Airbag) (Remove and Replace) - Updated link to airbag installation video.
- Foam - Back Rest - Driver Seat (Remove and Replace) - Updated link to airbag installation video.
- Seat Assembly - 2nd Row - LH (Without 2nd Row Bench Seats) (Remove and Replace) - Added step to perform a service CAN redeploy.
- - Updated link to airbag installation video.
Week Ending July 23, 2022
The following procedure(s) were updated:
- Firmware Reinstall - Toolbox - Added notes explaining why first redeploy fails and second redeploy should be successful.
- Fluid Capacities - added R1234yf
Week Ending July 16, 2022
The following procedure(s) were updated:
- Heat Exchanger - Front Drive Unit (Remove and Replace) - Added note to inspect and lubricate O-rings with EDF2 gearbox fluid.
- Heat Exchanger - Rear Drive Unit - LH (Plaid) (Remove and Replace) - Added note to inspect and lubricate O-rings with EDF2 gearbox fluid.
- Heat Exchanger - Rear Drive Unit (Long Range) (Remove and Replace) - Added note to inspect and lubricate O-rings with EDF2 gearbox fluid.
Week Ending July 9, 2022
The following procedure(s) were updated:
- Brake Rotor - Front - LH (Measure Runout) - Rephrased measurement criteria to decide whether brake rotor passes or fails.
- Brake Rotor - Rear - LH (Measure Runout) - Rephrased measurement criteria to decide whether brake rotor passes or fails.
- Inverter - Front Drive Unit (Plaid) (Remove and Replace) - Added phase bolt torque specifications for new bolts.
- Inverter - Front Drive Unit (Remove and Replace) - Procedure updated to remove the inverter from above, no longer needing to drop HV battery or front drive unit.
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Added phase bolt torque specifications for new bolts.
- Inverter - Rear Drive Unit (Remove and Replace) - Added phase bolt torque specifications for new bolts.
Week Ending July 2, 2022
The following new procedure(s) were added:
- Sensor - Parking Distance - Outer - Rear (HW3) (Remove and Replace)
Week Ending June 25, 2022
The following procedure(s) were updated:
- Oil Pump - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Added steps for oil pump configuration.
- Spoiler - Rear (Remove and Replace) - Relocated to section 1222 - Spoiler.
- Stabilizer Bar - Front (Remove and Replace) - Revised front subframe torque specifications.
- Brace - Toeboard - LH (Remove and Replace) - Revised front subframe torque specifications.
- Steering Rack (Remove and Replace) - Revised front subframe torque specifications.
- Subframe Assembly - Front (Remove and Install) - Revised front subframe torque specifications.
- All parking distance sensor procedures have been updated with the latest removal steps and Toolbox routines.
Week Ending June 4, 2022
The following procedure(s) were updated:
- Inverter - Rear Drive Unit (Remove and Replace) - Updated steps to retain 3-phase terminal bolts, torque them to 11.5 Nm, and to verify that no gap is stuck to gearbox housing.
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Updated steps to retain 3-phase terminal bolts, torque them to 11.5 Nm, and to verify that no gap is stuck to gearbox housing.
- Inverter - Front Drive Unit (Remove and Replace) - Updated steps to retain 3-phase terminal bolts, torque them to 11.5 Nm, and to verify that no gap is stuck to gearbox housing.
Week Ending May 28, 2022
The following procedure(s) were updated:
- Seat - Driver (Remove and Replace) - Updated tooling for seat removal.