07/11/2024 03:59:31

Correction code 33010702 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-11-07: Modified last step to instruct to add correction code for brake burnishing as a separate activity to the Service Visit.
  • 2023-03-28: Updated grease in installation section.
  • 2023-10-11: Updated the tools used to remove and install the bolts that attach the LH front brake caliper to the LH front knuckle.
Informational PurposesAn informational icon, calling your attention
Note
For detailed brake specifications, see Brakes.

Torque Specifications

Table 1. Torque Specifications: Brake Pad Kit - Front (Sport Brakes) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH front brake caliper to the LH front knuckle
94 Nm (69.3 lbs-ft)
  • External Torx E18
  • Cordless Ratchet/Impact Driver
Replace
Bolt that attaches the LH front brake hose bracket to the LH front knuckle
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • 4 in extension
Reuse

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Remove the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
  5. Remove and discard the bolts that attach the LH front brake caliper to the LH front knuckle.
    Tip: Use of the following tool(s) is recommended:
    • External Torx E18
    • Cordless Ratchet/Impact Driver
  6. Use a brake caliper S-hook to hang the LH front caliper on the body.
  7. Use a caliper spreader kit or similar tool to gently spread the brake pads apart.
  8. Gently use a plastic trim tool to remove the brake pads from the LH front brake caliper.
  9. Repeat step 3 through step 8 to remove the RH front brake pads.

Install

  1. Apply a thin layer of Silaramic grease to the left and right side edges of the LH front brake pads.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not apply any grease to the back side of the brake pad.
  2. Brush the LH front brake caliper and anti rattle springs with soapy water.
  3. Install the LH front brake pads on the LH front brake caliper.
    Tip: Push the pads toward the anti rattle springs, and then slide the pads onto the fixed pins.
  4. Position the LH front brake caliper onto the LH front knuckle, install new bolts that attach the caliper to the knuckle, and then mark the bolt with a paint pen.
    94 Nm (69.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • External Torx E18
    • Cordless Ratchet/Impact Driver
  5. Install the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  7. Repeat step 1 through step 6 to install the RH front brake pads.
  8. Lower the vehicle.
  9. Pump the brake pedal 3-5 times to seat the pads against the brake rotor until the brake pedal feels firm.
  10. Check the brake fluid reservoir and top off as necessary.
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  12. Perform a road test and burnish the brake pads. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure proper brake pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Add correction code 33013000 as a separate activity to the SV.