Release Notes April-June 2024

Archived Release Notes

Week Ending June 29, 2024

The following procedure(s) were updated:
  1. Speaker Grille - Instrument Panel (Remove and Replace) - Added instruction to release the speaker grille tabs by pulling up on the upper instrument panel trim.

Week Ending June 22, 2024

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Assembly - Brake Lines - Master Cylinder to HCU (RHD) (Remove and Replace) - Added step to perform test drive and add correction code 00040100 as a separate acitivity to the Service Visit.
  2. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated the inspection method and diagrams and added the tool list.
  3. Brake Caliper - Front (Sport Brakes) - RH (Remove and Replace) - Revised last step to either do a road test or perform brake pad burnishing procedure.
  4. Key Card (Remove and Replace) - Added picture to display how to pair the new key card.
  5. Brake Caliper - Rear (Sport Brakes) - RH (Remove and Replace) - Added step to either do a road test or perform brake pad burnishing procedure.
  6. Fascia - Rear - Upper (Remove and Replace) - Updated the step orders per the latest validation.
  7. Assembly - Brake Booster and Master Cylinder (RHD) (Remove and Replace) - Added step to perform test drive and add correction code 00040100 as a separate acitivity to the Service Visit.

Week Ending June 15, 2024

The following new procedure(s) were added:
  1. Brake Pads - Burnishing
The following procedure(s) were updated:
  1. Assembly - Brake Booster and Master Cylinder (LHD) (Remove and Replace) - Added step to perform a road test and add correction code 00040100 as a separate acitivity to the Service Visit.
  2. Airbag - Driver (Remove and Replace) - Updated information on tooling used to release the airbag springs. Added caution on avoiding cosmetic damage to the airbag release holes.
  3. Brake Caliper - Front (Sport Brakes) - LH (Remove and Replace) - Revised last step to either do a road test or perform brake pad burnishing procedure.
  4. Noise Absorber - Motor Bay - Front (Remove and Replace) - Added step to perform test drive and add correction code 00040100 as a separate acitivity to the Service Visit.
  5. Desiccant (Remove and Replace) - Added caution for Schrader valves.

Week Ending June 8, 2024

The following procedure(s) were updated:
  1. Brake Rotor - Rear (Base Brakes) - LH (Remove and Replace) - Added caution for correct rear brake hose installation.
  2. Combination Filter - HVAC (Remove and Replace) - Added cabin filter health score reset for SW versions 2024.14+
  3. Clean And Lubricate Brake Calipers (Performance Brakes) (Requires Code 34012501) (Maintenance) - Added caution for correct rear brake hose installation.
  4. Firmware Update - Mobile Connector - Added steps to update Mobile Connector firmware on vehicles operating software version 2024.14+.
  5. Brake Pad Kit - Rear (Base Brakes) (Remove and Replace) - Added caution for correct rear brake hose installation.
  6. Vehicle HV Disablement Procedure - Added warning to measure the specified order of locations for high voltage.
  7. Window Regulator (Recalibrate) (Module Reset/Reflashed) - Updated calibration steps using the touchscreen.

Week Ending June 1, 2024

The following procedure(s) were updated:
  1. Applique - B-Pillar - LH (Remove and Replace) - Updated the routines per the latest validation.

Week Ending May 25, 2024

The following procedure(s) were updated:
  1. Updated all "Vehicle Electrical Isolation Procedure" references to "Vehicle HV Disablement Procedure".

Week Ending May 18, 2024

The following procedure(s) were updated:
  1. Telematics Control Unit (TCU) (Remove and Replace) - Updated the removal/installation method per the latest validation and added instruction to remove the SIM card, if equipped.
  2. Module - Restraint Control - Universal (Remove and Replace) - Replaced Toolbox 3 routines by routines using the touchscreen.
  3. LV Battery - Li-lon (Disconnect and Connect) - Added steps to disconnect charging cable and shut down HVAC.
  4. Service Mode Plus - Added Service Mode Plus activation using the Vehicle Ops App.
  5. Trailer Hitch - Rear Energy Absorber (Retrofit) - Added instructions to prevent corrosion on EU trailer sockets.

Week Ending May 11, 2024

The following procedure(s) were updated:
  1. Center Console (Remove and Replace) - Added step for connector removal at RH front side of center console.
  2. HV Harness - A/C Compressor (Remove and Replace) - Added steps of reworking the new A/C compressor HV harness.

Week Ending May 4, 2024

The following procedure(s) were updated:
  1. ECU - Charge Port (Gen4) (Remove and Replace) - Updated torque specification for the charge port ECU bolt.
  2. Subframe Assembly - Rear (Remove and Replace) - Updated the way of performing the routines from using Toolbox to using the touchscreen.
  3. Tire Rotation - Added instructions on how to reset tire rotation through the vehicle touchscreen.

Week Ending April 27, 2024

The following procedure(s) were updated:
  1. Supermanifold (Remove and Replace) - Added steps of calculating the oil amount of desiccant bag and accumulator, and changed the way of removing the supermanifold from the vehicle directly to removing the supermanifold together with the shock tower brace and the compressor, and then separating the supermanifold from the assembly.
  2. Coolant Pump - HV Battery (Remove and Replace) - Updated the UI routines.

Week Ending April 20, 2024

The following procedure(s) were updated:
  1. Exterior Fittings - Luggage Compartment Trim - Front Luggage Storage Compartment - Frunk Reinforcement Assembly - Added steps of separating the cooling fan module isolation bracket from the old frunk reinforcement assembly and installing it to the new frunk reinforcement assembly.
  2. Harness - Main Front (Remove and Replace) - Updated the cover image.
  3. Bracket - Fascia Side to Fender - LH (Remove and Replace) - Updated the front fascia LH corner bolt torque from 4 Nm to 2.5 Nm.
  4. Harness - Fascia -Front (Remove and Replace) - Added a note to clarify that it is not necessary to remove the front fascia harness, valance and grille from the front fascia assembly.
  5. Fascia - Front (Remove and Replace) - Updated the front fascia upper bolt torque from 4 Nm to 3.5 Nm; the LH and RH corner bolts torque from 4 Nm to 2.5 Nm.
  6. Crush Can - Upper - Front - LH (Remove and Replace) - Added steps of removing/installing the front fascia.
  7. Subframe Assembly -Front (Remove and Replace) - Updated the front fascia to vehicle torque specification from 4 Nm to 2.5 Nm.
  8. Subframe Assembly -Front (Remove and Replace) - Updated front lower lateral link to subframe torque specification.
  9. HV Battery (RWD) \(Remove and Replace\) - Updated the correction code to 1601010132.
  10. Panel - Cowl Screen (Remove and Replace) - Removed the underhood storage unit related steps, and changed the shock tower cover removal steps to partially tucking the covers inside.

Week Ending April 13, 2024

The following new procedure(s) were added:
  1. Headlights - Adjust - NA (Tool Method)
The following procedure(s) were updated:
  1. Seal - Body - Side - Rear - Primary - RH (Remove and Replace) - Updated the LH primary rear side body seal images and the number of the clips.
  2. Applique - B-Pillar - LH (Remove and Replace) - Updated the LH B-pillar applique images and added steps of removing/installing the clips that attach the applique seal to the body.
  3. Glass - Body - Rear Quarter - LH (Remove and Replace) - Added steps of removing the rear quarter glass seal.
  4. Lumbar Support - Backrest - Driver Seat (Remove and Replace) - Add software reinstall step.
  5. LV Battery (Remove and Replace) - Added a Note to perform the recovery of the LV battery per Toolbox article prior to its replacement.
  6. Desiccant (Remove and Replace) - Added reminding of wearing PPEs.

Week Ending April 6, 2024

The following new procedure(s) were added:
  1. Insulators - HV Battery (Remove and Install)
The following procedure(s) were updated:
  1. NVH Pad - IP Carrier (Remove and Replace) - Updated the reference topic.
  2. Fluids and Capacities - Added new Gearbox Fluid section.
  3. Headlights - Adjust - Global (Wall Method) - Updated measurements and units.
  4. Thermistor - Duct (Remove and Replace) - Fixed the broken links.
  5. Desiccant (Remove and Replace) - Added reminding of checking the pressure of A/C system before opening the accumulator.