Current Release Notes

Archived Release Notes

Week Ending December 21,2024

The following new procedure(s) were added:
  1. Tweeter - Front Door - LH (Remove and Replace) - Deleted steps to remove/install Blind Spot Collision Warning device from/to tweeter.
The following procedure(s) were updated:
  1. Fixed missing torque specification "+ ## degrees".

Week Ending December 14, 2024

The following new procedure(s) were added:
  1. New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. The Pre-Installation Glass Inspection procedure explains how to inspect new windshield, roof, door, and fixed glass components before the new component is installed.
The following procedure(s) were updated:
  1. Added a new caution about Pre-Installation Glass Inspection service requirements:
  2. Four Wheel Alignment Check and Adjust - Removed note to add 00040100. FRT now includes test drive.
  3. Frame - Seat Cushion - Front Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  4. Motor - Seat Tilt - Front Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  5. Seat Assembly - 1st Row - LH (Remove and Replace) - Added mini-tilt motor configuration information.
  6. Seat Assembly - 1st Row - No Lumbar - RH (Remove and Replace) - Added mini-tilt motor configuration information.
  7. Steering Wheel (Remove and Replace) - Rearranged install steps.

Week Ending December 7, 2024

The following procedure(s) were updated:
  1. Updated inverter fastener torque sequence.
  2. Steering Column (LHD) (Remove and Replace) - Updated steering column configuration and calibration steps.
  3. Steering Column (RHD) (Remove and Replace) - Updated steering column configuration and calibration steps.

Week Ending November 30, 2024

The following new procedure(s) were added:
  1. Jumper Harness - Trailer Hitch (Remove and Replace)

Week Ending November 23, 2024

The following procedure(s) were updated:
  1. Headrest - Front Seat (Sport Seat) (Remove and Replace) - Corrected removal step to pull headrest towards the front of the vehicle for removal.
  2. LV Battery (Remove and Replace) - Added a note to remind of checking the 12V/LV battery temperature before performing the procedure.
  3. Performance Badge - Rear (Remove and Replace) - Added 1967007-00-A - REAR GRAPHIC BADGE JIG 2024+ Model 3 part number and note.

Week Ending November 16, 2024

The following new procedure(s) were added:
  1. Brake Pad Kit - Front (Sport Brakes) (Remove and Replace).
The following procedure(s) were updated:
  1. Height Adjuster - Seatbelt - LH (Remove and Replace) - Updated the torque information of the bolt that attaches the D-ring to the height adjuster from 20 Nm to 30 Nm.
  2. Webbing Guide Bar - Seatbelt - 1st Row (Single Side) (Remove and Replace) - Updated the torque info of the bolts that attach the 1st row webbing guide bar to the vehicle from 3.5 Nm to 5 Nm.

Week Ending November 9, 2024

The following procedure(s) were updated:
  1. HV Battery (RWD) \(Remove and Replace\) - Updated HV battery discharge steps.
  2. HV Battery (AWD) \(Remove and Replace\) - Updated HV battery discharge steps. Added AC harness steps for 3-phase packs.
  3. Steering Wheel (Remove and Replace) - Added step to perform Steering Wheel Post Replacement Procedure.

Week Ending November 2, 2024

The following new procedure(s) were added:
  1. Windshield Chip Repair (EMEA).
The following procedure(s) were updated:
  1. Headrest - Front Seat (Sport Seat) (Remove and Replace) - Added a note specifying headrest build dates and serviceability.
  2. LV Battery (Remove and Replace) - Added a Note about replacing the LV battery with different types.

Week Ending October 26, 2024

The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Added note on using self tapping bolts when installing the new car computer to the bulkhead.
  2. Clean Forward Camera View (Precision Cleaning of Inboard Glass) - Added a video demonstrating precision cleaning of windshield.
  3. Trunk (Remove and Replace) - Added a reminder for technicians to install all badges that are equipped with the working vehicle.

Week Ending October 19, 2024

The following new procedure(s) were added:
  1. Car Computer (Dispose).
The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Removed individual instructions for car computer scrapping and added cross reference to Car Computer (Dispose) topic.

Week Ending October 12, 2024

The following new procedure(s) were added:
  1. Brake Hydraulic Control Unit (Remove and Replace)
  2. Subframe Assembly - Rear (Partial Drop) (Remove and Install) - Do not use this procedure by itself. This procedure should only be used when it is referenced by another procedure.
The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Added instructions for scrapping.

Week Ending October 5, 2024

The following new procedure(s) were added:
  1. Event Data Recorder Retrieval
  2. Sensor - Wheel Speed - Front - LH (Performance) (Remove and Replace)
The following procedure(s) were updated:
  1. Parking Brake - Caliper - Rear - LH (Release) - Added information for Performance brakes and updated section title.