Release Notes October-December 2023

Week Ending December 30, 2023

The following new procedure(s) were added:
  1. Software Update
  2. Frame - Back Rest - Front Seat (Remove and Replace)
  3. Float Wing - Instrument Panel (Remove and Replace)
The following procedure(s) were updated:
  1. Switch - Steering Wheel - LH (Remove and Replace) - Added Software Reinstall and updated connector image.
  2. Shroud - Lower - Steering Column (Remove and Replace) - Added a step about installing the locator slot before installing the screws securing the lower shroud.

Week Ending December 23, 2023

The following new procedure(s) were added:
  1. Sensor - Pressure Tube - Pedestrian Protection (Remove and Replace)

Week Ending December 16, 2023

The following new procedure(s) were added:
  1. Handle - Exterior Release - Door - Rear - LH (Remove and Replace)
  2. Temperature and Humidity Sensor (Remove and Replace)
The following procedure(s) were updated:
  1. Assembly - Brake Lines - Rear - RH (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  2. Door - Front - LH (Remove and Install) - Updated correction code.
  3. Door - Front - LH (Remove and Replace) - Updated correction code.
  4. Inverter - Front Drive Unit (3DU) (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  5. Glass - Door - LH - Front (Adjust) - Updated the original nonadjustable correction code to the new adjustable one.
  6. Glass - Door - LH - Rear (Adjust) - Updated the original nonadjustable correction code to the new adjustable one.
  7. Rear Drive Unit - Mosfet - HC (3DU) (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  8. Breather - Rear Drive Unit (3DU) (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  9. Ground Strap - Rear Drive Unit (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  10. Mount - Rear Drive Unit - LH (3DU) (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.
  11. Steering Rack (LHD) (Remove and Replace) - Updated last step with cross reference to Alignment Requirement Tables.

Week Ending December 9, 2023

The following new procedure(s) were added:
  1. Tesla Badge - Rear (China) (Remove and Replace)
The following procedure(s) were updated:
  1. Tesla Badge - Rear (Remove and Replace) - Updated the procedure according to the latest validation.
  2. LV Battery (Remove and Replace) - Updated configuration steps for different types of Li-Ion battery.

Week Ending December 2, 2023

The following new procedure(s) were added:
  1. Brake Pad Kit - Front (Base Brakes) (Remove and Replace)
  2. Brake Pad Kit - Rear (Base Brakes) (Remove and Replace)
  3. Assembly - Brake Pedal (RHD) (Remove and Replace)
  4. Fender Assembly - Front - LH (Remove and Install)
  5. Fender Assembly - Front - LH (Remove and Replace)
  6. Door - Rear - LH (Remove and Install)
  7. Door - Front - LH (Remove and Install)
  8. Door - Front - LH (Remove and Replace)
  9. IP Carrier (Remove and Install)
  10. Fender Alignment

Week Ending November 25, 2023

The following new procedure(s) were added:
  1. Charge Port (EU) (Remove and Replace)
  2. Door Assembly - Charge Port (EU) (Remove and Replace)
The following procedure(s) were updated:
  1. Charge Port Voltage Check - Updated procedure and added images for EU charge port.
  2. Safety Cap - Busbar - Charge Port to HV Battery (3-Phase) (Remove and Replace) - Added instructions and images for EU charge port.
  3. Underhood Apron - Rear (Remove and Replace) - Update to keep the first responder loop label from visible to not visible after installation.

Week Ending November 17, 2023

The following new procedure(s) were added:
  1. ECU - Charge Port (Gen4) (Remove and Replace)

Week Ending November 10, 2023

The following new procedure(s) were added:
  1. Bracket - License Plate - Front (AU) (Retrofit using Jig)
  2. Bracket - License Plate - Front (EMEA) (Retrofit using Jig)
  3. Bracket - License Plate - Rear (EMEA) (Remove and Replace)
  4. Trailer Hitch - Rear Energy Absorber (Retrofit)

Week Ending November 3, 2023

The following procedure(s) were updated:
  1. Armrest - Center Console (Remove and Install) - Added missing info on removing/installing 2 additional screws in Removal step 10 and Installation step 2.