Release Notes January-March 2024

Archived Release Notes:

Week Ending March 30, 2024

The following procedure(s) were updated:
  1. Device Cluster Assembly (Remove and Install) - Cleaned up topic
  2. Device Cluster Assembly (Remove and Replace) - Cleaned up topic.
  3. Exterior Trim Fittings - C-Pillar Applique - LH (Remove and Install) - Added step to remove/install sail baffle applique.
  4. Fan and Radiator - Cooling Fan Module (Remove and Install) - Added steps to remove/install CFM lower bolts.
  5. Fluids - Added DOT 4 BASF Hydraulan 404 brake fluid and KAF 1 for gearbox fluid.
  6. Forward Facing - Forward Bi - Cam (Remove and Install) - Added step to set vehicle ride height.
  7. Forward Facing - Forward Bi - Cam (Remove and Replace) - Added step to set vehicle ride height.
  8. Four Wheel Alignment Check (No Adjustment Needed) - Updated ride height measurement underbody reference points.
  9. Four Wheel Alignment Check and Adjust - Updated ride height measurement underbody reference points.
  10. Frunk Assembly (Remove and Install) - Added information on the frunk switch connector locking pin.
  11. Rear Steering Gear and Lower Column - Rear Steering Actuator (Remove and Install) - Added steps to remove rear toe link and steps to load suspension to ride height during install.
  12. Rear Steering Gear and Lower Column - Rear Steering Actuator (Remove and Replace) - Added steps to remove rear toe link and steps to load suspension to ride height during install.
  13. Underhood Trim - Rear Apron Assembly (Remove and Install) - Added information on aligning the apron seal with the windshield seal.

Week Ending March 23, 2024

The following procedure(s) were updated:
  1. ABS Module and ESC Sensor - Hydraulic Control Unit (Remove and Install) - Added steps to bleed the brakes, and rearranged steps to streamline procedure.
  2. Brake Pedal - Brake Pedal - Option (Remove and Install) - Cleaned up topic.
  3. Dash, IP and Console Harnesses - IP (Remove and Install) - Cleaned up topic.
  4. Fluids - Added compressor oil density note and leak detection kit info.
  5. NVH Damping and Paint Armor - Dash Absorber - LH (Remove and Install) - Cleaned up topic.
  6. Rear Drive Inverter - Drive Inverter (Remove and Replace) - Updated torque specification for the lower tub crossmember bolts.
  7. Rear Drive Unit - Inverter, Mount, C1PM (Remove and Install) - Cleaned up topic.

Week Ending March 16, 2024

The following new procedure(s) were added:
  1. 1st Row Seat Belts - 1R LH Retractor, Black (Remove and Install)
  2. 1st Row Seat Belts - Single Fastener Seatbelt Webguide (Remove and Install)
  4. Cabin HVAC - Harness - Megavac, Center (Remove and Install)
  5. Electromechanical Brake Booster - Brake Remote Reservoir (Remove and Install)
  6. Electromechanical Brake Booster - Remote Reservoir Tube (Remove and Install)
  7. Frunk and Cabin Harnesses - Harness - Left Frunk (Remove and Install)
  8. NVH Damping and Paint Armor - Dash Absorber - LH (Remove and Install)
  9. Supermanifold - Harness - Supermanifold W/ Standalone Controller, Center (Remove and Install)
  10. Windshield and Backlite - Fixed Glass Backlite (Remove and Install)
The following procedure(s) were updated:
  1. Bed and Backbone Harnesses - Harness - MV Backbone (Remove and Install) - Cleaned up topic.
  2. Fixed Glass Roof Assembly (Remove and Replace) - Cleaned up topic.
  3. Rear Steering Gear and Lower Column - Rear Toe Link (Remove and Install) - Added Toolbox steps and step to raise suspension to ride height.
  4. Supermanifold - Octovalve (Remove and Install) - Cleaned up topic.
  5. Updated torque values:

Week Ending March 9, 2024

The following new procedure(s) were added:
  1. Body Panel (Refinish)
  2. Fixed Glass Roof Assembly (Remove and Replace)
  3. Replacement Tire Information
The following procedure(s) were updated:
  1. A/C Refrigerant (Recovery and Recharge) - Added step to reconnect MV power if disconnected during removal of component.
  2. Retrofit Cybertruck CyberTent (Retrofit) - Added basecamp retrofit kit box hardware installation steps.
  3. Charge Port - BUSBar Chargeport Assembly (Remove and Install) - Updated DC FC header greasing steps.
  4. Charge Port - BUSBar Chargeport Assembly (Remove and Replace) - Updated DC FC header greasing steps.
  5. Check Strap - Front Door - LH (Remove and Replace) - Updated check device joint bolt and torque.
  6. Cooling System (Vacuum Refill) - Added step to perform Thermal System Test routine.
  7. Dash Panel - Instrument Panel Lower Assembly (Remove and Install) - Revised quantity of x4 screws, T20 securing the RH lower IP to the vehicle.
  8. Front Seat Sliders and Controllers - 1R Seat Inboard Riser LH (Remove and Replace) - Added torque values for inboard riser to vehicle and inboard riser to crossmember.
  9. Check Strap, Rear (Remove and Replace) - Updated check device joint bolt and torque.
  10. Switch - Tonneau (Remove and Install) - Added the adhesive tape to the installation steps.