Release Notes July-September 2024

Archived Release Notes:

Week Ending September 28, 2024

The following new procedure(s) were added:
  1. Front Bumper Fascia - Front Fascia (Remove and Replace)
  2. Ride Height Calibration
  3. Tonneau Slat Assembly - Slat System - Tonneau (Rework)
The following procedure(s) were updated:
  1. Electromechanical Brake Booster - Brake Booster Assembly (Remove and Install) - Updated steps to latest time study. Added correction code for remove and replace.
  2. Front Steering Gear and Lower Column - Front Steering Actuator (Remove and Install) - Updated steps to latest time study.
  3. Front Steering Gear and Lower Column - Front Steering Actuator (Remove and Replace) - Updated the remove and install procedure to the latest time study.
  4. Height Controller and Sensors - Front Air Suspension Height Sensor Assembly - LH (Remove and Install) - Updated steps for calibration vehicle ride height to linked procedure. Ride height calibration procedure updated with expandable alignment specifications and ride height setting.
  5. Height Controller and Sensors - Rear Air Suspension Height Sensor Assembly - LH (Remove and Install) - Updated ride height calibration steps.

Week Ending September 21, 2024

The following new procedure(s) were added:
  1. HV Battery Contactor Seize Check
  2. Isolation/Insulation Test
The following procedure(s) were updated:
  1. Air Suspension Pressure Lines - Left Airline Bundle (Remove and Install) - Updated to latest study.
  2. Front Drive Inverter - Drive Inverter (Remove and Replace) - Added steps for phase plugs and arc shield.
  3. HV Battery (AWD) \(Remove and Install\) - Updated to latest time study.
  4. HV Battery (AWD) \(Remove and Replace\) - Updated to latest time study.
  5. How To Use This Manual - Added information on the crowsfoot/offset wrench extension calculator.
  6. HV Harness - AC Compressor \(Remove and Install\) - Updated to latest time study.
  7. Trailer Hitch - Tow Hitch (Remove and Install) - Updated fastener installation steps for patch bolts and torque value.

Week Ending September 14, 2024

The following new procedure(s) were added:
  1. Air Suspension Pressure Lines - Air Lines Leak (Inspection)
The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Added owner authorization request and MV maintainer steps.
  2. Disconnect MV Power - Updated MV battery reconnection process.
  3. HV Battery (AWD) \(Remove and Replace\) - Added step to connect MV maintainer.
  4. Supermanifold - Service Kit, Desiccant (Remove and Install) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.
  5. Tonneau - Tonneau NVH Barrier Assembly (Remove and Install) - Updated steps to include Rev-2 of component.
  6. Truck Bed - Bed Floor Assembly (Remove and Install) - Added cautions to note and correctly install shorter fasteners at the front of the bed floor assembly.
  7. Added link to video for best practices and servicing Super Connectors.

Week Ending September 7, 2024

The following procedure(s) were updated:
  1. Cabin HVAC - HVAC Distribution (Remove and Install) - Removed front rack calibration UI steps.
  2. Clean Forward Camera View (Precision Cleaning of Inboard Glass) - Added step to clean wiper blades.
  3. Four Wheel Alignment Check (No Adjustment Needed) - Removed duplicate front and rear steering rack calibration check step.
  4. Front Steering Gear and Lower Column - Front Steering Actuator (Remove and Install) - Removed front rack calibration UI steps.
  5. Front Steering Gear and Lower Column - Front Steering Actuator (Remove and Replace) - Added note to position vehicle on alignment turn plates prior to front rack calibration routine.
  6. Harness - Steering Jumper (Remove and Install) - Removed front rack calibration UI steps.
  7. Steering Column and Wheel - Steering Column Control Module (Remove and Install) - Removed front rack calibration UI steps.
  8. Steering Column and Wheel - Steering Column Control Module (Remove and Replace) - Removed front rack calibration UI steps.
  9. Steering Column and Wheel - Steering Wheel Harness (Remove and Install) - Removed front rack calibration UI steps.
  10. Steering Column and Wheel - Steering Wheel Switch - LH (Remove and Install) - Removed front rack calibration UI steps.
  11. Steering Column and Wheel - Steering Wheel Switch - LH (Remove and Replace) - Removed front rack calibration UI steps.
  12. Steering Column and Wheel - Steering Wheel Switch - RH (Remove and Install) - Removed front rack calibration UI steps.
  13. Steering Column and Wheel - Steering Wheel Switch - RH (Remove and Replace) - Removed front rack calibration UI steps.
  14. Windshield Wipers and Motor - Assembly, Wiper Motor (Remove and Install) - Added step to reinstall the vehicle software.

Week Ending August 31, 2024

The following new procedure(s) were added:
  1. Chassis and Subframes - Rear Subframe (Dual Motor) (Remove and Replace)
The following procedure(s) were updated:
  1. GUID-26B9B31C-85A6-4ED5-B326-B470F1D3CE61.html - Added missing step to set the ride height to "Medium".
  2. Windshield and Backlite - Fixed Glass Backlite (Remove and Install) - Added urethane bead size.

Week Ending August 24, 2024

The following new procedure(s) were added:
  1. GUID-26B9B31C-85A6-4ED5-B326-B470F1D3CE61.html
  2. Clean And Lubricate Brake Calipers (Integrated Parking Brake) (Requires Code 34012501) (Maintenance)
  3. Clean Forward Camera View (Precision Cleaning of Inboard Glass)
  4. Device Cluster Assembly (Backup and Restore)
  5. Rear Bumper Fascia - Rear Fascia (Remove and Replace)
  6. Steering Gear and Lower Column - Steering Gear Inner Tie Rod - LH (Remove and Replace)
The following procedure(s) were updated:
  1. Bed and Backbone Harnesses - Harness - MV Backbone (Remove and Install) - Added steps to align cable over rear rib and check for and install seam protection.
  2. Body Controllers - Rear Controller (Remove and Install) - Added step to check backbone harness alignment over rear rib and install anti-abrasion tape if missing.
  3. Body Controllers - Right Controller (Remove and Install) - Added steps to check for and install a backbone harness guide.
  4. Brake Lines - Master Cylinder - HCU Brake Pipe Assembly (Remove and Install) - Updated Brake Stiffness routine.
  5. Calipers and Pads - Rear Brake Caliper - Bleed Screw - LH (Remove and Install) - Updated Brake Stiffness routine.
  6. HV Battery (AWD) \(Remove and Install\) - Added steps to install backbone harness guide if the guide is not present.
  7. Passenger Compartment Carpet - End Item, Passenger Carpet Assembly, Soft Trim (Remove and Install) - Added steps to check for and install backbone harness guide.
  8. Passenger Compartment Carpet - End Item, Rear Carpet Assembly, Soft Trim (Remove and Install) - Added step to check backbone harness alignment and install anti-abrasion tape if missing.
  9. Power Conversion System (Remove and Replace) - Added/rearranged steps according to latest time study.
  10. Rear Brake Rotors - Calipers and Pads - Rear Brake Caliper - LH (Remove and Install) - Updated Brake Stiffness routine.
  11. Rear Brake Rotors - Calipers and Pads - SVC Rear Brake Caliper - LH (Without Pads) (Remove and Install) - Updated Brake Stiffness routine.
  12. Rear Drive Inverter - Drive Inverter (Remove and Replace) - Rearrange bootloader steps to the correct order.

Week Ending August 17, 2024

The following new procedure(s) were added:
  1. MV Battery - Recover - Please send us feedback on this procedure!
The following procedure(s) were updated:
  1. Center Console - Armrest Assembly (Remove and Install) - Updated steps for new armrest.
  2. HV Battery (AWD) \(Remove and Install\) - Added PN of anti-abrasion tape.
  3. HV Battery (AWD) \(Remove and Replace\) - Added PN of anti-abrasion tape.
  4. Power Conversion System (Remove and Replace) - Added/rearranged steps according to latest time study.
  5. Retrofit Cybertruck CyberTent (Retrofit) - Added step to remove tent from packaging.
  6. Slat System - Tonneau (Remove and Install) - Updated multiple step instructions, images, and tools according to latest time study.

Week Ending August 10, 2024

The following new procedure(s) were added:
  1. Body Controllers - MV Locking Cover Circlip (Remove and Replace)
  2. Exterior Trim Fittings - Roof Applique - Standalone - LH (Rework)
The following procedure(s) were updated:
  1. Cabin HVAC - HVAC Distribution (Remove and Install) - Updating images and fastener counts for multiple steps.
  2. Front Luggage Storage Compartment - Frunk Access Panel (Remove and Install) - Added note for newer versions of the access panels.
  3. Supermanifold - Service Kit, Coolant Bottle (Remove and Install) - Added note and video to step for removing coolant from coolant bottle.
  4. Updated sail applique steps for full replacement:

Week Ending August 3, 2024

The following procedure(s) were updated:
  1. Trim - Roof Rail - LH (Remove and Install) - Updated step to discard front fastener that attaches the cantrail to the vehicle.
  2. Exterior Trim Fittings - Roof Applique Bracket (Remove and Install) - Updated step for installing the bracket and securing the fastener.
  3. Front Drive Unit Assembly - Front Drive Unit (Remove and Replace) - Updated Toolbox routine.

Week Ending July 27, 2024

The following new procedure(s) were added:
  1. Brake Lines - Left Brake Tube Pipe Assembly (Remove and Install)
The following procedure(s) were updated:
  1. Off Road Lightbar (Mount on Windshield and Solder Only) (Retrofit) - Added link to CD-24-90-001.
  2. Four Wheel Alignment Check and Adjust - Added step to run Center and Hold routine. Rearranged steps.
  3. Toolbox 3 (Connect and Disconnect) - Added notes for different connector types.
  4. Front Steering Gear and Lower Column - Front Steering Actuator (Remove and Replace) - Added steps to connect/disconnect Toolbox.
  5. Device Cluster Assembly (Remove and Replace):
    • Added steps to check and adjust orientation of the shunts on replacement device cluster assembly before installing.
    • Added steps to back up and restore DCA; removed old placeholder steps.
  6. Update wiper motor homing step for better visibility, and add caution for wiper damage if step is skipped.

Week Ending July 20, 2024

The following procedure(s) were updated:
  1. HV Battery (AWD) \(Remove and Install\) - Updated rear interior HV battery bolt steps: in addition to the 13 mm bolts, some vehicles might also have 15 mm bolts.

Week Ending July 6, 2024

The following new procedure(s) were added:
  1. Powergate (Manual Release)
The following procedure(s) were updated:
  1. Added steps to run battery health test.
  2. Exterior Trim Fittings - Wiper Applique Assembly (Remove and Install) - Added instructions to squeeze the inboard clip while applying upward pressure to avoid damage, and step to release top edge with trim tool.
  3. Off Road Lightbar (Mount on Windshield and Solder Only) (Retrofit) - Added step for installing blackout film tape on lightbar.